Showing results: 76 - 90 of 202 items found.
-
72-7226 CAL D -
Tenma
The 72-7226 CAL D from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
Analog Devices Inc.
Analog Devices’ RF VGAs, IF VGAs, and variable gain control products offer the high performance needed for communications, instrumentation, and military designs. The portfolio includes continuous analog linear in dB products based on X-AMP® interpolation architectures and digital step controlled products providing as fine as 0.25 dB step and linear in volts digital control. Furthermore, ADI RF VGAs are highly integrated with digitally controlled multipole analog filters integrated on-chip as well as AGC circuits for automatic level control.
-
LAB / SL -
ET System Electronic GmbH
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
CP RC -
OMICRON electronics
For HV testing OMICRON’s CPC 100 + CP RC are directly connected to the voltage transformer of the GIS, forming a resonance circuit. This reinforced “Power VT” is an integrated part of the GIS. So the need for draining and refilling any SF6 gas is eliminated. Acting as both the measuring and controlling device, the CPC 100 injects the required energy.
-
GaGe
Performing real-time digital signal processing (DSP) routines such as Fast Fourier Transform (FFT), Signal Averaging, Finite Impulse Response (FIR) Filtering, Digital Down Conversion (DDC) and more have traditionally required the use of dedicated DSP processors, Field Programmable Gate Arrays (FPGAs), or Application Specific Integrated Circuits (ASICs).
-
CX-400 Ver.2 -
Panasonic Industrial Devices Sales Company of America
For the CX-400 Series, the user has a large selection of ultra compact Photoelectric Sensors at his disposal. The Series includes three thru-beam, five retro-reflective, four diffuse reflective and four trigonometric types with foreground/background suppression. With its new ASIC (application specific integrated circuit), the Sensors require up to 60% less energy than before.
-
Insight Product Company
Insight Product Company offers Microwave Silicon Limiter PIN Diodes with p+-i-n+ structures are designed to be used in microwave protective  devices included in hybrid integrated circuit (HIC) hermetically sealed, design of which provides protection against  moisture, salt, fog, mycelial fungus, hoarfrost, dew, decreased and increased pressure.
-
infraTest Prüftechnik GmbH
Cooling bath circulation thermostats - freezing test set of equipment 2 pieces for carrying out the freezing test with 42-2260 .... Complete with insulated connection hoses and connection elements as well as integrated circulating pumps for temperature control of a single or double sample. The temperature setting is software-controlled. For connection, 2 separate fused circuits per 16 A are required.
-
V‑Series -
Keysight Technologies
The highest real-time oscilloscope measurement accuracy. Keysight uses a proprietary indium phosphide (InP) integrated circuit process to design the key technology blocks to deliver high-bandwidth performance, ultra-low noise, low jitter, and high-voltage signal input. The InP process lets you see your true signal and make the most accurate measurements.
-
T-4 Series -
Picoprobe
T-4 tips are for use in most standard commercial micropositioners for probing integrated circuits, pads, or lines. Each T-4 tip uses the same 10, 22, 35, 60, or 125 micron diameter tungsten wire as our Model 12C Picoprobe, but is mounted to a 0.020 inch diameter, 2 inch long tinned copper shaft.
-
DRK218 -
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
Thermal Engineering Associates, Inc.
Thermal test system combines the test and measurement capability of dedicated instruments with the ease of operation and data collecting capability offered by graphical-user-interface-driven software operating on an integrated computer.Diodes (PN, Schottky, LED, varactor, PIN), Stacked Diodes (Hi-V Rectifiers & LEDs), Laser Diodes, Transistors (Bipolar, MOSFET, IGBT) & Diodes, Integrated Circuits (Application & Thermal Test Die).
-
CD15 -
Validyne Engineering
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
-
781964-02 -
NI
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
781964-03 -
NI
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
